 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| D100EHI Series Low Cost, Miniature SIP 1W, Very High Isolation DC/DC Converters Electrical Specifications Specifications typical @ +25C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: * 1W Output Power * 6,000 VDC Isolation * 7 Pin SIP Case * 5V and 12V Inputs * Single & Dual Outputs * 16 Standard Models * 3.5 MH MTBF * LOWEST COST!! Input Parameter Input Voltage Range Input Filter Short Circuit Input Power Conditions 5 VDC Input 12 VDC Input Min. 4.5 10.8 Typ. 5.0 12.0 Max. 5.5 13.2 1,500 Conditions Dual Output , Balanced Loads For Vin Change of 1% Iout = 10% to 100% Iout = 10% to 100% 250 120 0.01 Momentary (1.0 Seconds) Conditions 60 Seconds 500 VDC 100 kHz, 1V 5 VDC Input 12 VDC Input 250 50 Min. Ambient -40 -55 Free Air Convection RH, Non-condensing 95 % Typ. Max. +85 +125 Units C C Min. 6,000 1,000 20 Typ. Max. Units VDC M pF kHz 0.03 Min. Typ. 2.0 1.0 Max. 4.0 3.0 1.2 15 10 300 Units VDC Internal Capacitor mW Units % % %/% % % mV P - P % %/C Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation, 5V Input Load Regulation, 12V & 24V Input Ripple & Noise (20 MHz) (Note 1) Output Power Protection Temperature Coefficient RoHS Compliant Output Short Circuit General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Conditions MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Humidity Physical Case Size Case Material Weight 0.77 x 0.38 x 0.50 Inches (19.5 x 9.8 x 12.5 mm) Non-Conductive Black Plastic (UL94-V0) 0.42 Oz (12g) Conditions MIL HDBK 217F, 25C, Gnd Benign Conditions 5 VDC Input 12 VDC Input 1.5 mm From Case For 10 Sec. All Models Min. 3.5 Min. -0.7 -0.7 Typ. Max. 7.5 15.0 300 1,500 Typ. Max. Units MHours Units VDC C mW Reliability Specifications Parameter MTBF Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Input Model Number D101EHI D102EHI D103EHI D104EHI D105EHI D106EHI D107EHI D108EHI D111EHI D112EHI D113EHI D114EHI D115EHI D116EHI D117EHI D118EHI Voltage (VDC) Nominal 5 5 5 5 5 5 5 5 12 12 12 12 12 12 12 12 Range 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 Current (mA) Full-Load 286 286 278 278 277 277 267 267 113 113 110 110 111 111 107 107 No-Load 60 60 60 60 60 60 60 60 40 40 40 40 40 40 40 40 Voltage (VDC) 5.0 9.0 12.0 15.0 5.0 9.0 12.0 15.0 5.0 9.0 12.0 15.0 5.0 9.0 12.0 15.0 Output Current Current (mA, Max) (mA, Min) 200 111 84 67 100 56 42 33 200 111 84 67 100 56 42 33 20.0 12.0 9.0 7.0 10.0 6.0 5.0 4.0 20.0 12.0 9.0 7.0 10.0 6.0 5.0 4.0 Efficiency (%, Typ) 72 72 75 75 72 72 75 75 74 74 76 76 75 75 78 78 Fuse Rating Slow-Blow (mA) 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 250 250 250 250 250 250 250 250 Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ceramic Input Output capacitor be placed Vin Vout Capacitor Capacitor from the +Vout pin to the -Vout pin for 5 VDC 4.7 F 5 VDC 4.7 F single output units 12 VDC 2.2 F 9 VDC 2.2 F and from each out12 VDC 1.0 F put to common for 15 VDC 0.47 F dual output units. An input capacitor will enhance stability over temperature and input line variations. Recommended capacitor values are given in the table above. For applications requiring very low output noise levels, a simple Pi filter should be effective. Component values would depend upon the application, but capacitor values of 4.7 F and inductor values of 10 H are often sufficient. 4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Derating Curve Mechanical Dimensions Pin Connections Pin 1 2 5 6 7 Single +Vin -Vin -Vout No Pin +Vout Dual +Vin -Vin -Vout Common +Vout Mechanical Notes: * All dimensions are typical in inches (mm) * Tolerance x.xx = 0.01 (0.25) MicroPower Direct www.micropowerdirect.com * 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 * FAX: (781) 344-8481 * E-Mail: sales@micropowerdirect.com |
Price & Availability of D103EHI
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |